TDA7294 100 + 100 watt stereo amplifier board price

---

New  PCB having 2 x TDA7294 ic and Power Supply.

4700uf x 2 Capacitors and GBU 10 Ampere Rectifier.

Just Add a Transformer and your High Power Stereo Amplifier is ready. 

the Same Reliable Circuit of Tusker just Double the power.

What TUSKER has achieved in this short period is exceptional.

Tusker is simple, easy to make and delivers high power with many types of speakers.

You may ask why the name “TUSKER”, after all it is a small pcb.

What can I say, small number of Tuskers ( Not the Truck, but Elephants ) still roam the forests of our country, they are Majestic.)

And now you will get 2 of them on 1  pcb.

• High Output - 100 watt RMS output power using 8 ohms speakers.*
• Low Distortion - 0.1% Total Harmonic Distortion at 20 watt output using 8 ohms speakers and 1KHz sine wave input.*
• Speaker usability - 4 & 8 ohms, 50 watt to 200 watt speakers can be used.*
• Supply voltage -  12 volts to 40 volts DC supply working range.*
• Transformer Recommended - 24 0 24 VAC  5 - 8  Ampere 
• Standard Components - All components used are available online or at your local electronics store. 
• No SMD components used - Only through hole components used, making soldering and replacement hassle free.  
• Low cost  - This amplifier can be made in a fraction of cost compared to similar amplifiers available in market. 

     * as per TDA7294 STMicroelectronics datasheet.

• Subwoofer Amplifier - High power amplification of low frequency sound.
•  Musical instrument amplifier - Frequency response 20 Hz to 20 KHz, you can amplify any instrument like Guitar, Keyboard, Banjo.
• Amplified speaker box - Compact size board that can be fitted inside the speaker enclosure.
•  Stereo Amplifier - Listen to your favorite songs in clarity never experienced before. 

                                                              Only 1 channel is described, the other channel works the same.

Power Supply Rectifier - Bridge Rectifier D1 ( GBU1010 or GBU810 ) is used to rectify the incoming 

AC Voltage in to DC, the DC is Further smoothed by Capacitor C1 and C2 ( 4700uf 50v ) 

Amplifier - Main job of amplification is done by ic U1 and rest are the supporting components.

Input signal is fed  to pin no.3 (Non Inverting Input) through R1 & C3. R2 defines the input impedance. 

R3 & R4 connected to Pin no.2 (Inverting input) set the closed loop gain. Changing the value of any one these resistors will change the gain of the amplifier. 

Pin no.9 (Stand by) - R7 keeps ic U1 in active mode by providing positive voltage.

Pin no. 7, 13 are positive supply, Pin no. 8, 15 are negative supply and 1, 4 are ground pins. Pin no.14 is the output pin.

Mute Function - Pin no.10 (Mute) is connected to JP2. To use the mute function replace JP2 with a switch.

 Metal Tab of ic U1 is connected to negative supply internally, so  proper insulation is necessary when fitting ic U1 on heatsink. 

  Amplifier IC                          

                                U1 / U2  -   TDA7293, TDA7294, TDA7295, TDA7296

 Bridge Rectifier

                                    D1  -  GBU1004 -1010   GBU8005 - 810   GBU8A -8M     

                   *Supply voltages and output power vary, please read datasheet carefully.

• Type of PCB  - Single sided, Glass Epoxy FR-4 Grade A  
• PCB Size - 132 mm x 60 mm (5.2 inch x 2.3 inch ), pcb Thickness - 1.6 mm.
• Thickness of copper on PCB - 35 micrometer 

PCB designed with thick copper tracks & large solder pads to facilitate straightforward  placement and soldering of components.